Kundservice Snabb leverans For företag och privat
Betyg
0 0

Kommentering är inte påslagen på denna kursen.

3. 3M TM Protective Coverall 4515 Test Standard/Test Method Class/ Result Abrasion resistance (visual assessment) EN 530:2010 Class 1 Flex cracking (visual assessment) ISO 7854:1995 Class 5 Tear resistance ISO 9073-4:1997 Class 2 Tensile strength EN ISO 13934-1:1999 Class 1 Puncture resistance EN 863:1995 Class 1 Resistance to ignition EN 13274-4:2001 Pass Seam strength EN ISO 13935-2:1999 Class 3 Repellency to liquids – 30% H 2 SO 4 EN ISO 6530:2005 Class 3 of 3 Test Standard/Test Method Class/ Result Liquid penetration resistance – 30% H 2 SO 4 EN ISO 6530:2005 Class 3 of 3 Repellency to liquids – 10% NaOH EN ISO 6530:2005 Class 3 of 3 Liquid penetration resistance – 10% NaOH EN ISO 6530:2005 Class 3 of 3 Radioactive particulates (TIL) EN 1073-2:2002 Class 1 of 3 The table shows the performance of this product when tested under laboratory conditions in accordance with the referenced standard test method. Note: The maximum Class is 6 unless otherwise noted. Personal Safety Division 3M Centre Cain Road, Bracknell Berkshire RG12 8HT www.3M.eu/safety 3M is a trademark of 3M Company. Please recycle. Printed in the United Kingdom. © 3M 2019. All rights reserved. Version: 4515.2 IMPORTANT NOTICE The use of the 3M product described within this document assumes that the user has previous experience of this type of product and that it will be used by a competent professional. Before any use of this product it is recommended to complete some trials to validate the performance of the product within its expected application. All information and specification details contained within this document are inherent to this specific 3M product and would not be applied to other products or environment. Any action or usage of this product made in violation of this document is at the risk of the user. Compliance to the information and specification relative to the 3M product contained within this document does not exempt the user from compliance with additional guidelines (safety rules, procedures). Compliance to operational requirements especially in respect to the environment and usage of tools with this product must be observed. The 3M group (which cannot verify or control those elements) would not be held responsible for the consequences of any violation of these rules which remain external to its decision and control. Warranty conditions for 3M products are determined with the sales contract documents and with the mandatory and applicable clause, excluding any other warranty or compensation. Visit the 3M Chemical Test Library for an online repository of available chemical data for 3M TM Protective Coveralls: http://go.3M.com/CHTL

2. Storage and Disposal • Store in dry, clean conditions in original packaging, away from direct sunlight, sources of high temperature, and solvent vapours • Store within the temperature range -20°C to +25°C (-4°F to +77°F) and with relative humidity below 80% • Expected shelf life is five (5) years from date of manufacture when stored as stated 3 • Replace garments if damaged, heavily contaminated or in accordance with local work practice or regulations • Handle and dispose of contaminated garments with care and in accordance with applicable regulations 3 The shelf life as defined above remains an indicative and maximum data, subject to many external and non-controllable factors. It may never be interpreted as a warranty. Limited Use 4 The chemicals against which the product has been tested and certified are listed in the user instructions and shown in the following table. For additional chemical penetration data, please call your local 3M Technical Service Representative or visit the 3M Chemical Test library on http://go.3M.com/ CHTL In all cases, a risk assessment should be carried out. Always read product user information. Use limitations and performance data should be considered to ascertain the protection required. If in doubt, contact a safety professional. For more information on 3M products and services please contact 3M. Warnings and Limitations Before use read and understand all user instructions and be sure that the product is suitable for the application and fitted correctly. Product must never be altered or modified. Do not use for: • Contact with heavy oils, sparks or flame, or combustible liquids; • Environments with high mechanical risks (abrasions, tears, cuts); • Contact with hazardous substances beyond Type 5/6 certification; • Environments with conditions of excessive heat. 3M TM Protective Coverall 4515 Applications and Performance Non-Hazardous Particulates Yes Hazardous Liquid Splash Yes, if chemical is compatible with suit material 4 Non-Hazardous Liquid Splash Particulates Yes Hazardous Liquid Spray No Hazardous Dusts and Fibres Yes Organic Solvents No Liquid Continuous Contact/ Immersion No Acids/ Alkalis Yes, if chemical is compatible with suit material 4 Gases and Vapours No Do not wash Do not dry clean Do not bleach Flammable — keep away from sparks or flames Do not iron Single Use - do not re-use Do not tumble dry

1. 3M™ Protective Coverall 4515 Technical Data Sheet Description The 3M™ Protective Coverall 4515 is designed to help protect against hazardous dusts (Type 5) and certain light liquid splashes (Type 6). Colour options: white, blue or orange. Comfort and Protection 2 The values above are the result of illustrative lab test measures and should not be considered as a commitment from 3M Height Chest S 64 – 67 in 164 – 170 cm 33 - 36 in 84 – 92 cm M 66 – 69 in 167 – 176 cm 36 – 39 in 92 – 100 cm L 69 – 71 in 174 – 181 cm 39 – 43 in 100 – 108 cm XL 70 – 74 in 179 – 187 cm 43 – 45 in 108 – 115 cm XXL 73 – 76 in 186 – 194 cm 45 – 49 in 115 – 124 cm 3XL 76 – 78 in 194 – 200 cm 49 – 52 in 124 – 132 cm 4XL 78 – 81 in 200 – 206 cm 52 – 55 in 132 – 140 cm Except EN863 puncture resistance. Does not offer protection against radiation. Approvals These products are type examined by SATRA Technology Europe Ltd., Notified body number 2777 and audited annually by SGS, Notified Body number 0598. These products are CE marked to the requirements of European Regulation (EU) 2016/425.The applicable legislation can be determined by reviewing the Certificate and Declaration of Conformity at www.3m.com/Body/certs Materials Suit SMS Polypropylene 50gsm (standard material on all colour options) Zipper Nylon on Polyester Braid Elastic Synthetic Rubber (non-latex) Thread Polyester/ Cotton Sizing 2 An appropriate size garment should be selected to allow sufficient movement for the task whilst maintaining a secure fit. Type 6 - Light Liquid Splashes Protection (EN 13034:2005 +A1:2009) Radioactive particulates (EN 1073-2:2002) Class 1 Type 5 - Solid Airborne Particulates (EN ISO 13982-1:2004 +A1:2010) Liquid Protection Dust Protection Nuclear This product does not contain components made from silicone or natural rubber latex.

Säkerhet för alla

Håll dig säkert uppdaterad med de senaste nyheterna och kunskapen inom PPE och arbetsmiljö